tag:blogger.com,1999:blog-5384807982946756823.post3974243808545115408..comments2024-02-09T00:35:38.406-08:00Comments on Simply Cycle: Soma Buena Vista with Nuvinci HubMarchttp://www.blogger.com/profile/11240252773932276478noreply@blogger.comBlogger8125tag:blogger.com,1999:blog-5384807982946756823.post-54646628447296780392011-05-22T14:04:40.127-07:002011-05-22T14:04:40.127-07:00Thanks, as you can tell there's been some thou...Thanks, as you can tell there's been some thought over that one.Marchttps://www.blogger.com/profile/11240252773932276478noreply@blogger.comtag:blogger.com,1999:blog-5384807982946756823.post-66379666970762648932011-05-21T17:31:51.357-07:002011-05-21T17:31:51.357-07:00Just saw your build. It is a head turner for sure....Just saw your build. It is a head turner for sure.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-5384807982946756823.post-20807282824359833072011-04-15T10:53:47.483-07:002011-04-15T10:53:47.483-07:00I don't see that it will be a problem, especia...I don't see that it will be a problem, especially with the forged dropout. I figured, my issue is peculiar to the Nuvinci hub, but I just haven't gotten down and measured them both to see what the difference is. I'm looking forward to seeing your build.Marchttps://www.blogger.com/profile/11240252773932276478noreply@blogger.comtag:blogger.com,1999:blog-5384807982946756823.post-60806256561788182572011-04-15T07:40:39.636-07:002011-04-15T07:40:39.636-07:00The Shimano's axle, while having flats, can st...The Shimano's axle, while having flats, can still rotate within the dropout. As you know, Shimano supplies anti-rotation washers, which are keyed to the axle flats and have a tab which locks them into the dropout, and sharp teeth that really bite into the dropout. They specify torquing the axle nuts to 35 lb-ft, which is fairly tight. My only concern is that the dropout is so long that any torque placed on the lower finger of the dropout is multiplied by being so far forward. But, since you haven't had a problem with either setup, I'm not going to worry about it!somervillainhttps://www.blogger.com/profile/13903377050982678550noreply@blogger.comtag:blogger.com,1999:blog-5384807982946756823.post-89290988645787094212011-04-15T05:17:33.451-07:002011-04-15T05:17:33.451-07:00The brake reach is a concern, but I don't expe...The brake reach is a concern, but I don't expect a problem with the dropouts. I had my Shimano IGH in a similar position on the Raleigh mixte and had no problem. Those were stamped steel which are much weaker. How well does the Shimano axle fit the dropouts? The Nuvinci barely fits on the flat sides only,I was shocked but haven't stopped long enough to compare the specs.Marchttps://www.blogger.com/profile/11240252773932276478noreply@blogger.comtag:blogger.com,1999:blog-5384807982946756823.post-79072426054940158902011-04-14T14:36:00.715-07:002011-04-14T14:36:00.715-07:00Marc,
Another question about Byron... I noticed y...Marc,<br /><br />Another question about Byron... I noticed your axle is about as far forward in the dropout as possible. I take it the reason is because any farther back, and the long-reach brakes wouldn't be long enough to reach the rim, right? I ran into the same situation assembling the brakes on my wife's Soma last night. As a result, her Shimano Nexus 8 hub is positioned the same as yours. Are you at all concerned about the torque applied to the dropout by the axle? I know these hubs use anti-rotation washers torqued down really tight, but I've heard stories about dropouts opening up and bending with IGHs. Frankly, I'm a little concerned-- only because the axle is so far forward, creating more leverage to bend the dropout. Thoughts?somervillainhttps://www.blogger.com/profile/13903377050982678550noreply@blogger.comtag:blogger.com,1999:blog-5384807982946756823.post-74450722321854882512011-03-11T07:12:40.594-08:002011-03-11T07:12:40.594-08:00It would depend on the handlebars. The frame does...It would depend on the handlebars. The frame does have an aggressive and "sporty" geometry, but the Albotross bars reach back and create a more upright position. I have mine inverted to create more reach because of my long torso. I'm sure that using them in a normal position with a short stem, set higher than the saddle would be really comfortable for a "normal" person. Any reason is a good reason to spend 2k on a bike. Wear skirts more often, recover the cost faster!Marchttps://www.blogger.com/profile/11240252773932276478noreply@blogger.comtag:blogger.com,1999:blog-5384807982946756823.post-37153338141435336192011-03-10T12:28:48.874-08:002011-03-10T12:28:48.874-08:00Marc - I've been drooling over the Soma Buena ...Marc - I've been drooling over the Soma Buena Vista for a while (already have three bikes!), but the mixte would be great for riding to work when I'm wearing a skirt. Great reason to spend 2K, eh? Anyway, I'm 5'3", looking at the 42 cm version, but seeing reviews by women that the top tube makes it a long reach. I'm looking for a more laid back townie style. What are your thoughts?juliehttps://www.blogger.com/profile/01163778014472211660noreply@blogger.com